Help with SSL

Problems with the Windows version of XAMPP, questions, comments, and anything related.

Help with SSL

Postby smurfier » 17. February 2020 05:40

I've been working on setting SSL for my server with no luck. Any help would be appreciated.

httpd.conf
Code: Select all
#
# This is the main Apache HTTP server configuration file.  It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
# for a discussion of each configuration directive.
#
# Do NOT simply read the instructions in here without understanding
# what they do.  They're here only as hints or reminders.  If you are unsure
# consult the online docs. You have been warned. 
#
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path.  If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "logs/access_log"
# with ServerRoot set to "/usr/local/apache2" will be interpreted by the
# server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log"
# will be interpreted as '/logs/access_log'.
#
# NOTE: Where filenames are specified, you must use forward slashes
# instead of backslashes (e.g., "c:/apache" instead of "c:\apache").
# If a drive letter is omitted, the drive on which httpd.exe is located
# will be used by default.  It is recommended that you always supply
# an explicit drive letter in absolute paths to avoid confusion.

#
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
#
# Do not add a slash at the end of the directory path.  If you point
# ServerRoot at a non-local disk, be sure to specify a local disk on the
# Mutex directive, if file-based mutexes are used.  If you wish to share the
# same ServerRoot for multiple httpd daemons, you will need to change at
# least PidFile.
#
Define SRVROOT "C:/xampp/apache"

ServerRoot "C:/xampp/apache"

#
# Mutex: Allows you to set the mutex mechanism and mutex file directory
# for individual mutexes, or change the global defaults
#
# Uncomment and change the directory if mutexes are file-based and the default
# mutex file directory is not on a local disk or is not appropriate for some
# other reason.
#
# Mutex default:logs

#
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
#
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#
#Listen 12.34.56.78:80
Listen 80

#
# Dynamic Shared Object (DSO) Support
#
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
#
# Example:
# LoadModule foo_module modules/mod_foo.so
#
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule actions_module modules/mod_actions.so
LoadModule alias_module modules/mod_alias.so
LoadModule allowmethods_module modules/mod_allowmethods.so
LoadModule asis_module modules/mod_asis.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule auth_form_module modules/mod_auth_form.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
LoadModule authn_core_module modules/mod_authn_core.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authn_socache_module modules/mod_authn_socache.so
#LoadModule authnz_fcgi_module modules/mod_authnz_fcgi.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
LoadModule authz_core_module modules/mod_authz_core.so
#LoadModule authz_dbd_module modules/mod_authz_dbd.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_host_module modules/mod_authz_host.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
LoadModule authz_user_module modules/mod_authz_user.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule brotli_module modules/mod_brotli.so
#LoadModule buffer_module modules/mod_buffer.so
#LoadModule cache_module modules/mod_cache.so
#LoadModule cache_disk_module modules/mod_cache_disk.so
#LoadModule cache_socache_module modules/mod_cache_socache.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
LoadModule cgi_module modules/mod_cgi.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule data_module modules/mod_data.so
#LoadModule dav_module modules/mod_dav.so
#LoadModule dav_fs_module modules/mod_dav_fs.so
LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule dbd_module modules/mod_dbd.so
#LoadModule deflate_module modules/mod_deflate.so
LoadModule dir_module modules/mod_dir.so
#LoadModule dumpio_module modules/mod_dumpio.so
LoadModule env_module modules/mod_env.so
#LoadModule expires_module modules/mod_expires.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
#LoadModule file_cache_module modules/mod_file_cache.so
#LoadModule filter_module modules/mod_filter.so
#LoadModule http2_module modules/mod_http2.so
LoadModule headers_module modules/mod_headers.so
#LoadModule heartbeat_module modules/mod_heartbeat.so
#LoadModule heartmonitor_module modules/mod_heartmonitor.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule imagemap_module modules/mod_imagemap.so
LoadModule include_module modules/mod_include.so
LoadModule info_module modules/mod_info.so
LoadModule isapi_module modules/mod_isapi.so
#LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
#LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
#LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
#LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
#LoadModule ldap_module modules/mod_ldap.so
#LoadModule logio_module modules/mod_logio.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_debug_module modules/mod_log_debug.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule lua_module modules/mod_lua.so
LoadModule cache_disk_module modules/mod_cache_disk.so
#LoadModule macro_module modules/mod_macro.so
#LoadModule md_module modules/mod_md.so
LoadModule mime_module modules/mod_mime.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
LoadModule negotiation_module modules/mod_negotiation.so
LoadModule proxy_module modules/mod_proxy.so
LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
#LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
#LoadModule proxy_connect_module modules/mod_proxy_connect.so
#LoadModule proxy_express_module modules/mod_proxy_express.so
#LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
#LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
#LoadModule proxy_hcheck_module modules/mod_proxy_hcheck.so
#LoadModule proxy_html_module modules/mod_proxy_html.so
#LoadModule proxy_http_module modules/mod_proxy_http.so
#LoadModule proxy_http2_module modules/mod_proxy_http2.so
#LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule proxy_uwsgi_module modules/mod_proxy_uwsgi.so
#LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
#LoadModule ratelimit_module modules/mod_ratelimit.so
#LoadModule reflector_module modules/mod_reflector.so
#LoadModule remoteip_module modules/mod_remoteip.so
#LoadModule request_module modules/mod_request.so
#LoadModule reqtimeout_module modules/mod_reqtimeout.so
LoadModule rewrite_module modules/mod_rewrite.so
#LoadModule sed_module modules/mod_sed.so
#LoadModule session_module modules/mod_session.so
#LoadModule session_cookie_module modules/mod_session_cookie.so
#LoadModule session_crypto_module modules/mod_session_crypto.so
#LoadModule session_dbd_module modules/mod_session_dbd.so
LoadModule setenvif_module modules/mod_setenvif.so
#LoadModule slotmem_plain_module modules/mod_slotmem_plain.so
#LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
#LoadModule socache_dbm_module modules/mod_socache_dbm.so
#LoadModule socache_memcache_module modules/mod_socache_memcache.so
#LoadModule socache_redis_module modules/mod_socache_redis.so
LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
#LoadModule speling_module modules/mod_speling.so
LoadModule ssl_module modules/mod_ssl.so
LoadModule status_module modules/mod_status.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule unique_id_module modules/mod_unique_id.so
#LoadModule userdir_module modules/mod_userdir.so
#LoadModule usertrack_module modules/mod_usertrack.so
LoadModule version_module modules/mod_version.so
#LoadModule vhost_alias_module modules/mod_vhost_alias.so
#LoadModule watchdog_module modules/mod_watchdog.so
#LoadModule xml2enc_module modules/mod_xml2enc.so

<IfModule unixd_module>
#
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch. 
#
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
#
User daemon
Group daemon

</IfModule>

# 'Main' server configuration
#
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition.  These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
#
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
#

#
# ServerAdmin: Your address, where problems with the server should be
# e-mailed.  This address appears on some server-generated pages, such
# as error documents.  e.g. admin@your-domain.com
#
ServerAdmin postmaster@localhost

#
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
#
# If your host doesn't have a registered DNS name, enter its IP address here.
#
ServerName localhost:80

#
# Deny access to the entirety of your server's filesystem. You must
# explicitly permit access to web content directories in other
# <Directory> blocks below.
#
<Directory />
    AllowOverride none
    Require all denied
</Directory>

#
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
#

#
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
#
DocumentRoot "C:/xampp/htdocs"
<Directory "C:/xampp/htdocs">
    #
    # Possible values for the Options directive are "None", "All",
    # or any combination of:
    #   Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
    #
    # Note that "MultiViews" must be named *explicitly* --- "Options All"
    # doesn't give it to you.
    #
    # The Options directive is both complicated and important.  Please see
    # http://httpd.apache.org/docs/2.4/mod/core.html#options
    # for more information.
    #
    Options Indexes FollowSymLinks Includes ExecCGI

    #
    # AllowOverride controls what directives may be placed in .htaccess files.
    # It can be "All", "None", or any combination of the keywords:
    #   AllowOverride FileInfo AuthConfig Limit
    #
    AllowOverride All

    #
    # Controls who can get stuff from this server.
    #
    Require all granted
</Directory>

#
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
#
<IfModule dir_module>
    DirectoryIndex index.php index.pl index.cgi index.asp index.shtml index.html index.htm \
                   default.php default.pl default.cgi default.asp default.shtml default.html default.htm \
                   home.php home.pl home.cgi home.asp home.shtml home.html home.htm
</IfModule>

#
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
#
<Files ".ht*">
    Require all denied
</Files>

#
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here.  If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
#
ErrorLog "logs/error.log"

#
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
#
LogLevel warn

<IfModule log_config_module>
    #
    # The following directives define some format nicknames for use with
    # a CustomLog directive (see below).
    #
    LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
    LogFormat "%h %l %u %t \"%r\" %>s %b" common

    <IfModule logio_module>
      # You need to enable mod_logio.c to use %I and %O
      LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
    </IfModule>

    #
    # The location and format of the access logfile (Common Logfile Format).
    # If you do not define any access logfiles within a <VirtualHost>
    # container, they will be logged here.  Contrariwise, if you *do*
    # define per-<VirtualHost> access logfiles, transactions will be
    # logged therein and *not* in this file.
    #
    #CustomLog "logs/access.log" common

    #
    # If you prefer a logfile with access, agent, and referer information
    # (Combined Logfile Format) you can use the following directive.
    #
    CustomLog "logs/access.log" combined
</IfModule>

<IfModule alias_module>
    #
    # Redirect: Allows you to tell clients about documents that used to
    # exist in your server's namespace, but do not anymore. The client
    # will make a new request for the document at its new location.
    # Example:
    # Redirect permanent /foo http://www.example.com/bar

    #
    # Alias: Maps web paths into filesystem paths and is used to
    # access content that does not live under the DocumentRoot.
    # Example:
    # Alias /webpath /full/filesystem/path
    #
    # If you include a trailing / on /webpath then the server will
    # require it to be present in the URL.  You will also likely
    # need to provide a <Directory> section to allow access to
    # the filesystem path.

    #
    # ScriptAlias: This controls which directories contain server scripts.
    # ScriptAliases are essentially the same as Aliases, except that
    # documents in the target directory are treated as applications and
    # run by the server when requested rather than as documents sent to the
    # client.  The same rules about trailing "/" apply to ScriptAlias
    # directives as to Alias.
    #
    ScriptAlias /cgi-bin/ "C:/xampp/cgi-bin/"

</IfModule>

<IfModule cgid_module>
    #
    # ScriptSock: On threaded servers, designate the path to the UNIX
    # socket used to communicate with the CGI daemon of mod_cgid.
    #
    #Scriptsock cgisock
</IfModule>

#
# "C:/xampp/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
#
<Directory "C:/xampp/cgi-bin">
    AllowOverride All
    Options None
    Require all granted
</Directory>

<IfModule headers_module>
    #
    # Avoid passing HTTP_PROXY environment to CGI's on this or any proxied
    # backend servers which have lingering "httpoxy" defects.
    # 'Proxy' request header is undefined by the IETF, not listed by IANA
    #
    RequestHeader unset Proxy early
</IfModule>

<IfModule mime_module>
    #
    # TypesConfig points to the file containing the list of mappings from
    # filename extension to MIME-type.
    #
    TypesConfig conf/mime.types

    #
    # AddType allows you to add to or override the MIME configuration
    # file specified in TypesConfig for specific file types.
    #
    #AddType application/x-gzip .tgz
    #
    # AddEncoding allows you to have certain browsers uncompress
    # information on the fly. Note: Not all browsers support this.
    #
    #AddEncoding x-compress .Z
    #AddEncoding x-gzip .gz .tgz
    #
    # If the AddEncoding directives above are commented-out, then you
    # probably should define those extensions to indicate media types:
    #
    AddType application/x-compress .Z
    AddType application/x-gzip .gz .tgz

    #
    # AddHandler allows you to map certain file extensions to "handlers":
    # actions unrelated to filetype. These can be either built into the server
    # or added with the Action directive (see below)
    #
    # To use CGI scripts outside of ScriptAliased directories:
    # (You will also need to add "ExecCGI" to the "Options" directive.)
    #
    AddHandler cgi-script .cgi .pl .asp

    # For type maps (negotiated resources):
    #AddHandler type-map var

    #
    # Filters allow you to process content before it is sent to the client.
    #
    # To parse .shtml files for server-side includes (SSI):
    # (You will also need to add "Includes" to the "Options" directive.)
    #
    AddType text/html .shtml
    AddOutputFilter INCLUDES .shtml
</IfModule>

#
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type.  The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#
<IfModule mime_magic_module>
    #
    # The mod_mime_magic module allows the server to use various hints from the
    # contents of the file itself to determine its type.  The MIMEMagicFile
    # directive tells the module where the hint definitions are located.
    #
    MIMEMagicFile "conf/magic"
</IfModule>


#
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
#
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html
#

#
# MaxRanges: Maximum number of Ranges in a request before
# returning the entire resource, or one of the special
# values 'default', 'none' or 'unlimited'.
# Default setting is to accept 200 Ranges.
#MaxRanges unlimited

#
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall may be used to deliver
# files.  This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
# Defaults: EnableMMAP On, EnableSendfile Off
#
#EnableMMAP off
#EnableSendfile off

# Supplemental configuration
#
# The configuration files in the conf/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.

# Server-pool management (MPM specific)
Include conf/extra/httpd-mpm.conf

# Multi-language error messages
Include conf/extra/httpd-multilang-errordoc.conf

# Fancy directory listings
Include conf/extra/httpd-autoindex.conf

# Language settings
Include conf/extra/httpd-languages.conf

# User home directories
Include conf/extra/httpd-userdir.conf

# Real-time info on requests and configuration
Include conf/extra/httpd-info.conf

# Virtual hosts
Include conf/extra/httpd-vhosts.conf

# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf

# Distributed authoring and versioning (WebDAV)
#Attention! WEB_DAV is a security risk without a new userspecific configuration for a secure authentifcation
#Include conf/extra/httpd-dav.conf

# Various default settings
#Include conf/extra/httpd-default.conf
# Implements a proxy/gateway for Apache.
Include "conf/extra/httpd-proxy.conf"
# Various default settings
Include "conf/extra/httpd-default.conf"
# XAMPP settings
Include "conf/extra/httpd-xampp.conf"

# Configure mod_proxy_html to understand HTML4/XHTML1
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf
</IfModule>

# Secure (SSL/TLS) connections
Include conf/extra/httpd-ssl.conf
#
# Note: The following must must be present to support
#       starting without SSL on platforms with no /dev/random equivalent
#       but a statically compiled-in mod_ssl.
#
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>

# XAMPP: We disable operating system specific optimizations for a listening
# socket by the http protocol here. IE 64 bit make problems without this.

AcceptFilter http none
AcceptFilter https none
# AJP13 Proxy
<IfModule mod_proxy.c>
<IfModule mod_proxy_ajp.c>
Include "conf/extra/httpd-ajp.conf"
</IfModule>
</IfModule>

<IfModule mod_rewrite.c>
    RewriteEngine On

    # Redirect /xampp folder to https
    RewriteCond %{HTTPS} !=on
    RewriteCond %{REQUEST_URI} xampp
    RewriteRule ^(.*) https://%{SERVER_NAME}$1 [R,L]

    # Redirect /phpMyAdmin folder to https
    RewriteCond %{HTTPS} !=on
    RewriteCond %{REQUEST_URI} phpmyadmin
    RewriteRule ^(.*) https://%{SERVER_NAME}$1 [R,L]

    # Redirect /security folder to https
    RewriteCond %{HTTPS} !=on
    RewriteCond %{REQUEST_URI} security
    RewriteRule ^(.*) https://%{SERVER_NAME}$1 [R,L]

    # Redirect /webalizer folder to https
    RewriteCond %{HTTPS} !=on
    RewriteCond %{REQUEST_URI} webalizer
    RewriteRule ^(.*) https://%{SERVER_NAME}$1 [R,L]

    # Redirect /folder_name folder to https
    RewriteCond %{HTTPS} !=on
    RewriteCond %{REQUEST_URI} folder_name
    RewriteRule ^(.*) https://%{SERVER_NAME}$1 [R,L]

</IfModule>


httpd-ssl.conf
Code: Select all
#
# This is the Apache server configuration file providing SSL support.
# It contains the configuration directives to instruct the server how to
# serve pages over an https connection. For detailed information about these
# directives see <URL:http://httpd.apache.org/docs/2.4/mod/mod_ssl.html>
#
# Do NOT simply read the instructions in here without understanding
# what they do.  They're here only as hints or reminders.  If you are unsure
# consult the online docs. You have been warned. 
#
# Required modules: mod_log_config, mod_setenvif, mod_ssl,
#          socache_shmcb_module (for default value of SSLSessionCache)

#
# Pseudo Random Number Generator (PRNG):
# Configure one or more sources to seed the PRNG of the SSL library.
# The seed data should be of good random quality.
# WARNING! On some platforms /dev/random blocks if not enough entropy
# is available. This means you then cannot use the /dev/random device
# because it would lead to very long connection times (as long as
# it requires to make more entropy available). But usually those
# platforms additionally provide a /dev/urandom device which doesn't
# block. So, if available, use this one instead. Read the mod_ssl User
# Manual for more details.
#
#SSLRandomSeed startup file:/dev/random  512
#SSLRandomSeed startup file:/dev/urandom 512
#SSLRandomSeed connect file:/dev/random  512
#SSLRandomSeed connect file:/dev/urandom 512


#
# When we also provide SSL we have to listen to the
# standard HTTP port (see above) and to the HTTPS port
#
Listen 443

##
##  SSL Global Context
##
##  All SSL configuration in this context applies both to
##  the main server and all SSL-enabled virtual hosts.
##

#   SSL Cipher Suite:
#   List the ciphers that the client is permitted to negotiate,
#   and that httpd will negotiate as the client of a proxied server.
#   See the OpenSSL documentation for a complete list of ciphers, and
#   ensure these follow appropriate best practices for this deployment.
#   httpd 2.2.30, 2.4.13 and later force-disable aNULL, eNULL and EXP ciphers,
#   while OpenSSL disabled these by default in 0.9.8zf/1.0.0r/1.0.1m/1.0.2a.
#SSLCipherSuite HIGH:MEDIUM:!MD5:!RC4:!3DES
#SSLProxyCipherSuite HIGH:MEDIUM:!MD5:!RC4:!3DES

#  By the end of 2016, only TLSv1.2 ciphers should remain in use.
#  Older ciphers should be disallowed as soon as possible, while the
#  kRSA ciphers do not offer forward secrecy.  These changes inhibit
#  older clients (such as IE6 SP2 or IE8 on Windows XP, or other legacy
#  non-browser tooling) from successfully connecting. 
#
#  To restrict mod_ssl to use only TLSv1.2 ciphers, and disable
#  those protocols which do not support forward secrecy, replace
#  the SSLCipherSuite and SSLProxyCipherSuite directives above with
#  the following two directives, as soon as practical.
# SSLCipherSuite HIGH:MEDIUM:!SSLv3:!kRSA
# SSLProxyCipherSuite HIGH:MEDIUM:!SSLv3:!kRSA

#   User agents such as web browsers are not configured for the user's
#   own preference of either security or performance, therefore this
#   must be the prerogative of the web server administrator who manages
#   cpu load versus confidentiality, so enforce the server's cipher order.
SSLHonorCipherOrder on

#   SSL Protocol support:
#   List the protocol versions which clients are allowed to connect with.
#   Disable SSLv3 by default (cf. RFC 7525 3.1.1).  TLSv1 (1.0) should be
#   disabled as quickly as practical.  By the end of 2016, only the TLSv1.2
#   protocol or later should remain in use.
SSLProtocol all -SSLv3
SSLProxyProtocol all -SSLv3

#   Pass Phrase Dialog:
#   Configure the pass phrase gathering process.
#   The filtering dialog program (`builtin' is an internal
#   terminal dialog) has to provide the pass phrase on stdout.
SSLPassPhraseDialog  builtin

#   Inter-Process Session Cache:
#   Configure the SSL Session Cache: First the mechanism
#   to use and second the expiring timeout (in seconds).
#SSLSessionCache "shmcb:C:/xampp/apache/logs/ssl_scache(512000)"
SSLSessionCache "shmcb:C:/xampp/apache/logs/ssl_scache(512000)"
SSLSessionCacheTimeout  300

#   OCSP Stapling (requires OpenSSL 0.9.8h or later)
#
#   This feature is disabled by default and requires at least
#   the two directives SSLUseStapling and SSLStaplingCache.
#   Refer to the documentation on OCSP Stapling in the SSL/TLS
#   How-To for more information.
#
#   Enable stapling for all SSL-enabled servers:
#SSLUseStapling On

#   Define a relatively small cache for OCSP Stapling using
#   the same mechanism that is used for the SSL session cache
#   above.  If stapling is used with more than a few certificates,
#   the size may need to be increased.  (AH01929 will be logged.)
#SSLStaplingCache "shmcb:${SRVROOT}/logs/ssl_stapling(32768)"

#   Seconds before valid OCSP responses are expired from the cache
#SSLStaplingStandardCacheTimeout 3600

#   Seconds before invalid OCSP responses are expired from the cache
#SSLStaplingErrorCacheTimeout 600

##
## SSL Virtual Host Context
##

<VirtualHost _default_:443>

#   General setup for the virtual host
DocumentRoot "C:/xampp/htdocs"
ServerName www.example.com:443
ServerAdmin admin@example.com
ErrorLog "C:/xampp/apache/logs/error.log"
TransferLog "C:/xampp/apache/logs/access.log"

#   SSL Engine Switch:
#   Enable/Disable SSL for this virtual host.
#SSLEngine on

#   Server Certificate:
#   Point SSLCertificateFile "conf/ssl.crt/server.crt"
#   the certificate is encrypted, then you will be prompted for a
#   pass phrase.  Note that a kill -HUP will prompt again.  Keep
#   in mind that if you have both an RSA and a DSA certificate you
#   can configure both in parallel (to also allow the use of DSA
#   ciphers, etc.)
#   Some ECC cipher suites (http://www.ietf.org/rfc/rfc4492.txt)
#   require an ECC certificate which can also be configured in
#   parallel.

# HERE THIS ONE!!!!
#SSLCertificateFile "conf/ssl.crt/server.crt"
#SSLCertificateFile "conf/ssl.crt/server.crt"
#SSLCertificateFile "conf/ssl.crt/server.crt"

#   Server Private Key:
#   If the key is not combined with the certificate, use this
#   directive to point at the key file.  Keep in mind that if
#   you've both a RSA and a DSA private key you can configure
#   both in parallel (to also allow the use of DSA ciphers, etc.)
#   ECC keys, when in use, can also be configured in parallel

# HERE THIS ONE!!!!
#SSLCertificateKeyFile "conf/ssl.key/server.key"
#SSLCertificateKeyFile "conf/ssl.key/server.key"
#SSLCertificateKeyFile "conf/ssl.key/server.key"

#   Server Certificate Chain:
#   Point SSLCertificateChainFile at a file containing the
#   concatenation of PEM encoded CA certificates which form the
#   certificate chain for the server certificate. Alternatively
#   the referenced file can be the same as SSLCertificateFile "conf/ssl.crt/server.crt"
#   certificate for convenience.
#SSLCertificateChainFile "${SRVROOT}/conf/server-ca.crt"

#   Certificate Authority (CA):
#   Set the CA certificate verification path where to find CA
#   certificates for client authentication or alternatively one
#   huge file containing all of them (file must be PEM encoded)
#   Note: Inside SSLCACertificatePath you need hash symlinks
#         to point to the certificate files. Use the provided
#         Makefile to update the hash symlinks after changes.
#SSLCACertificatePath "${SRVROOT}/conf/ssl.crt"
#SSLCACertificateFile "${SRVROOT}/conf/ssl.crt/ca-bundle.crt"

#   Certificate Revocation Lists (CRL):
#   Set the CA revocation path where to find CA CRLs for client
#   authentication or alternatively one huge file containing all
#   of them (file must be PEM encoded).
#   The CRL checking mode needs to be configured explicitly
#   through SSLCARevocationCheck (defaults to "none" otherwise).
#   Note: Inside SSLCARevocationPath you need hash symlinks
#         to point to the certificate files. Use the provided
#         Makefile to update the hash symlinks after changes.
#SSLCARevocationPath "${SRVROOT}/conf/ssl.crl"
#SSLCARevocationFile "${SRVROOT}/conf/ssl.crl/ca-bundle.crl"
#SSLCARevocationCheck chain

#   Client Authentication (Type):
#   Client certificate verification type and depth.  Types are
#   none, optional, require and optional_no_ca.  Depth is a
#   number which specifies how deeply to verify the certificate
#   issuer chain before deciding the certificate is not valid.
#SSLVerifyClient require
#SSLVerifyDepth  10

#   TLS-SRP mutual authentication:
#   Enable TLS-SRP and set the path to the OpenSSL SRP verifier
#   file (containing login information for SRP user accounts).
#   Requires OpenSSL 1.0.1 or newer. See the mod_ssl FAQ for
#   detailed instructions on creating this file. Example:
#   "openssl srp -srpvfile ${SRVROOT}/conf/passwd.srpv -add username"
#SSLSRPVerifierFile "${SRVROOT}/conf/passwd.srpv"

#   Access Control:
#   With SSLRequire you can do per-directory access control based
#   on arbitrary complex boolean expressions containing server
#   variable checks and other lookup directives.  The syntax is a
#   mixture between C and Perl.  See the mod_ssl documentation
#   for more details.
#<Location />
#SSLRequire (    %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \
#            and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \
#            and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \
#            and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \
#            and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20       ) \
#           or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/
#</Location>

#   SSL Engine Options:
#   Set various options for the SSL engine.
#   o FakeBasicAuth:
#     Translate the client X.509 into a Basic Authorisation.  This means that
#     the standard Auth/DBMAuth methods can be used for access control.  The
#     user name is the `one line' version of the client's X.509 certificate.
#     Note that no password is obtained from the user. Every entry in the user
#     file needs this password: `xxj31ZMTZzkVA'.
#   o ExportCertData:
#     This exports two additional environment variables: SSL_CLIENT_CERT and
#     SSL_SERVER_CERT. These contain the PEM-encoded certificates of the
#     server (always existing) and the client (only existing when client
#     authentication is used). This can be used to import the certificates
#     into CGI scripts.
#   o StdEnvVars:
#     This exports the standard SSL/TLS related `SSL_*' environment variables.
#     Per default this exportation is switched off for performance reasons,
#     because the extraction step is an expensive operation and is usually
#     useless for serving static content. So one usually enables the
#     exportation for CGI and SSI requests only.
#   o StrictRequire:
#     This denies access when "SSLRequireSSL" or "SSLRequire" applied even
#     under a "Satisfy any" situation, i.e. when it applies access is denied
#     and no other module can change it.
#   o OptRenegotiate:
#     This enables optimized SSL connection renegotiation handling when SSL
#     directives are used in per-directory context.
#SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire
<FilesMatch "\.(cgi|shtml|phtml|php)$">
    SSLOptions +StdEnvVars
</FilesMatch>
<Directory "C:/xampp/apache/cgi-bin">
    SSLOptions +StdEnvVars
</Directory>

#   SSL Protocol Adjustments:
#   The safe and default but still SSL/TLS standard compliant shutdown
#   approach is that mod_ssl sends the close notify alert but doesn't wait for
#   the close notify alert from client. When you need a different shutdown
#   approach you can use one of the following variables:
#   o ssl-unclean-shutdown:
#     This forces an unclean shutdown when the connection is closed, i.e. no
#     SSL close notify alert is sent or allowed to be received.  This violates
#     the SSL/TLS standard but is needed for some brain-dead browsers. Use
#     this when you receive I/O errors because of the standard approach where
#     mod_ssl sends the close notify alert.
#   o ssl-accurate-shutdown:
#     This forces an accurate shutdown when the connection is closed, i.e. a
#     SSL close notify alert is send and mod_ssl waits for the close notify
#     alert of the client. This is 100% SSL/TLS standard compliant, but in
#     practice often causes hanging connections with brain-dead browsers. Use
#     this only for browsers where you know that their SSL implementation
#     works correctly.
#   Notice: Most problems of broken clients are also related to the HTTP
#   keep-alive facility, so you usually additionally want to disable
#   keep-alive for those clients, too. Use variable "nokeepalive" for this.
#   Similarly, one has to force some clients to use HTTP/1.0 to workaround
#   their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and
#   "force-response-1.0" for this.
BrowserMatch "MSIE [2-5]" \
         nokeepalive ssl-unclean-shutdown \
         downgrade-1.0 force-response-1.0

#   Per-Server Logging:
#   The home of a custom SSL log file. Use this when you want a
#   compact non-error SSL logfile on a virtual host basis.
CustomLog "C:/xampp/apache/logs/ssl_request.log" \
          "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b"

</VirtualHost>

<VirtualHost *:80>
   ServerName www.smurfier.com
   ServerAlias smurfier.com
   DocumentRoot "D:\Sites\tools"
   <Directory "D:\Sites\tools">
      AllowOverride All
      Require all granted
   </Directory>
</VirtualHost>

<VirtualHost *:443>
   ServerName www.smurfier.com
   ServerAlias smurfier.com
   ServerAdmin smurfier@outlook.com
   DocumentRoot "D:\Sites\tools"
   <Directory "D:\Sites\tools">
      AllowOverride All
      Require all granted
   </Directory>

   SSLEngine on
   SSLProtocol all -SSLv2
   #SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5:!SEED:!IDEA
   SSLCertificateFile "D:\SSL\smurfier.com\smurfier.crt"
   SSLCertificateKeyFile "D:\SSL\smurfier.com\smurfier.key"
   SSLCertificateChainFile "D:\SSL\smurfier.com\smurfier-ca.crt"
</VirtualHost>

<VirtualHost *:80>
   ServerName rawr.smurfier.com
   ServerAdmin smurfier@outlook.com
   DocumentRoot "D:\Sites\rawr"

   <Directory "D:\Sites\rawr">
      AllowOverride All
      Require all granted
   </Directory>
</VirtualHost>

<VirtualHost *:443>
   ServerName rawr.smurfier.com
   ServerAdmin smurfier@outlook.com
   DocumentRoot "D:\Sites\rawr"

   <Directory "D:\Sites\rawr">
      AllowOverride All
      Require all granted
   </Directory>

   SSLEngine on
   SSLCertificateFile "D:\SSL\smurfier.com\smurfier.crt"
   SSLCertificateKeyFile "D:\SSL\smurfier.com\smurfier.key"
   SSLCertificateChainFile "D:\SSL\smurfier.com\smurfier-ca.crt"
</VirtualHost>

<VirtualHost *:80>
   ServerName wheel.smurfier.com
   DocumentRoot "D:\Sites\wheel"
   <Directory "D:\Sites\wheel">
      AllowOverride All
      Require all granted
   </Directory>
</VirtualHost>


httpd-xampp.conf
Code: Select all
#
# XAMPP settings
#

<IfModule env_module>
    SetEnv MIBDIRS "C:/xampp/php/extras/mibs"
    SetEnv MYSQL_HOME "\\xampp\\mysql\\bin"
    SetEnv OPENSSL_CONF "C:/xampp/apache/bin/openssl.cnf"
    SetEnv PHP_PEAR_SYSCONF_DIR "\\xampp\\php"
    SetEnv PHPRC "\\xampp\\php"
    SetEnv TMP "\\xampp\\tmp"
</IfModule>

#
# PHP-Module setup
#
LoadFile "C:/xampp/php/php7ts.dll"
LoadFile "C:/xampp/php/libpq.dll"
LoadModule php7_module "C:/xampp/php/php7apache2_4.dll"

<FilesMatch "\.php$">
    SetHandler application/x-httpd-php
</FilesMatch>
<FilesMatch "\.phps$">
    SetHandler application/x-httpd-php-source
</FilesMatch>

#
# PHP-CGI setup
#
#<FilesMatch "\.php$">
#    SetHandler application/x-httpd-php-cgi
#</FilesMatch>
#<IfModule actions_module>
#    Action application/x-httpd-php-cgi "/php-cgi/php-cgi.exe"
#</IfModule>


<IfModule php7_module>
    PHPINIDir "C:/xampp/php"
</IfModule>

<IfModule mime_module>
    AddType text/html .php .phps
</IfModule>

ScriptAlias /php-cgi/ "C:/xampp/php/"
<Directory "C:/xampp/php">
    AllowOverride None
    Options None
    Require all denied
    <Files "php-cgi.exe">
          Require all granted
    </Files>
</Directory>

<Directory "C:/xampp/cgi-bin">
    <FilesMatch "\.php$">
        SetHandler cgi-script
    </FilesMatch>
    <FilesMatch "\.phps$">
        SetHandler None
    </FilesMatch>
</Directory>

<Directory "C:/xampp/htdocs/xampp">
    <IfModule php7_module>
       <Files "status.php">
          php_admin_flag safe_mode off
       </Files>
    </IfModule>
    AllowOverride AuthConfig
    SSLRequireSSL
</Directory>

<IfModule alias_module>
    Alias /licenses "C:/xampp/licenses/"
    <Directory "C:/xampp/licenses">
        Options +Indexes
        <IfModule autoindex_color_module>
            DirectoryIndexTextColor  "#000000"
            DirectoryIndexBGColor "#f8e8a0"
            DirectoryIndexLinkColor "#bb3902"
            DirectoryIndexVLinkColor "#bb3902"
            DirectoryIndexALinkColor "#bb3902"
        </IfModule>
        Require local
        ErrorDocument 403 /error/XAMPP_FORBIDDEN.html.var
   </Directory>

    Alias /phpmyadmin "C:/xampp/phpMyAdmin/"
    <Directory "C:/xampp/phpMyAdmin">
        AllowOverride AuthConfig
        Require local
        ErrorDocument 403 /error/XAMPP_FORBIDDEN.html.var
        SSLRequireSSL
    </Directory>

    Alias /webalizer "C:/xampp/webalizer/"
    <Directory "C:/xampp/webalizer">
        <IfModule php7_module>
          <Files "webalizer.php">
             php_admin_flag safe_mode off
          </Files>
        </IfModule>
        AllowOverride AuthConfig
        Require local
        ErrorDocument 403 /error/XAMPP_FORBIDDEN.html.var
        SSLRequireSSL
    </Directory>
</IfModule>
smurfier
 
Posts: 3
Joined: 17. February 2020 05:36
XAMPP version: 3.2.4
Operating System: Windows 10Pro

Re: Help with SSL

Postby Nobbie » 18. February 2020 12:52

smurfier wrote:I've been working on setting SSL for my server with no luck.


"No luck" is a very poor description. Could you tell us more detailled about your problems?
Nobbie
 
Posts: 11565
Joined: 09. March 2008 13:04

Re: Help with SSL

Postby smurfier » 18. February 2020 15:49

I'm getting this error: ERR_SSL_PROTOCOL_ERROR
smurfier
 
Posts: 3
Joined: 17. February 2020 05:36
XAMPP version: 3.2.4
Operating System: Windows 10Pro

Re: Help with SSL

Postby Nobbie » 18. February 2020 15:52

Still insuffient. Something is wrong with your Certificate (probably). Impossible to say more with that poor amount of information.
Nobbie
 
Posts: 11565
Joined: 09. March 2008 13:04

Re: Help with SSL

Postby gsmith » 18. February 2020 22:30

I see problems in the config so just rename your conf/httpd-ssl.conf to httpd-ssl.old and start out small. Once https://localhost works, then you should be able to just add your smurfier.com hosts.

Apache needs _default_ (fallback) hosts for virtual hosting to work properly (or you can get strange results). It's documented but hard to understand, has been changed a couple times with each change becoming even harder to understand.

This config below will;
1. Only allows TLS 1.2 & 1.3*. Firefox is doing away with TLS 1.0 & 1.1 this year and I expect others to follow close behind. Apache disabled SSLv3 back some time ago.
2. Whitelists protocols rather than blacklisting (just my preference).
3. Moves some items into the global config for use by all hosts. If any specific host needs other you can add same directives with different values into a specific vhost because vhost config overrides global config in Apache.
4. Allow the use of HTTP/2 provided you uncomment the loadmodule line for mod_http2 in your httpd.conf file.
5. Will NOT work with old clients that do not at least support TLS/1.2.
6. Does not allow downgrade attacks to get Apache using vulnerable SSL/TLS ciphers.

* Provided you have Apache 2.4.36 or above and not all clients support TLS/1.3 just yet so they will use TLS/1.2.

httpd-ssl.conf
Code: Select all
# If Apache version is 2.4.36 or above, uncomment the below line
#Define ENABLE_TLS13 "Yes"


<IfModule http2_module>
    ProtocolsHonorOrder On
    Protocols h2 h2c http/1.1
</IfModule>

##################################################################
# SSL Demo Configuration for Apache Haus Distribution
# FileName: conf/extras/mod_ahssl.conf
#
# This is the Apache server configuration file providing SNI support.
# It contains the configuration directives to instruct the server how to
# serve pages over an https connection. For detailed information about these
# directives see <URL:http://httpd.apache.org/docs/2.4/mod/mod_ssl.html>
#
# Do NOT simply read the instructions in here without understanding
# what they do.  They're here only as hints or reminders.  If you are unsure
# consult the online docs. You have been warned. 
#
# Required modules: mod_log_config, mod_setenvif, mod_ssl,
#          socache_shmcb_module (for default value of SSLSessionCache)


Listen 443 https

##
##  SSL Global Context
##
##  All SSL configuration in this context applies both to
##  the main server and all SSL-enabled virtual hosts.
##

#   SSL Protocols:
#   List the protocols that the client is permitted to negotiate.
#   See the mod_ssl documentation for a complete list.
#   SSL Cipher Suite:
#   List the ciphers that the client is permitted to negotiate.
#   See the mod_ssl documentation for a complete list.
<IfDefine ENABLE_TLS13>
  SSLProtocol -all +TLSv1.2 +TLSv1.3
  SSLCipherSuite SSL ECDHE-ECDSA-CHACHA20-POLY1305:ECDHE-RSA-CHACHA20-POLY1305:DHE-RSA-CHACHA20-POLY1305:ECDHE-RSA-AES256-GCM-SHA384:ECDHE-RSA-AES128-GCM-SHA256:DHE-RSA-AES256-GCM-SHA384:ECDHE-RSA-AES256-SHA384:ECDHE-RSA-AES256-SHA:DHE-RSA-AES256-SHA256:DHE-RSA-AES256-SHA:!RC4:!LOW:!MD5:!aNULL:!eNULL:!3DES:!EXP:!PSK:!SRP:!DSS
  SSLCipherSuite TLSv1.3 TLS_CHACHA20_POLY1305_SHA256:TLS_AES_256_GCM_SHA384:TLS_AES_128_GCM_SHA256
</IfDefine>

<IfDefine !ENABLE_TLS13>
SSLProtocol -all +TLSv1.1 +TLSv1.2
SSLCipherSuite ECDHE-ECDSA-CHACHA20-POLY1305:ECDHE-RSA-CHACHA20-POLY1305:DHE-RSA-CHACHA20-POLY1305:ECDHE-RSA-AES256-GCM-SHA384:ECDHE-RSA-AES128-GCM-SHA256:DHE-RSA-AES256-GCM-SHA384:ECDHE-RSA-AES256-SHA384:ECDHE-RSA-AES256-SHA:DHE-RSA-AES256-SHA256:DHE-RSA-AES256-SHA:!RC4:!LOW:!MD5:!aNULL:!eNULL:!3DES:!EXP:!PSK:!SRP:!DSS
SSLProxyCipherSuite ECDHE-ECDSA-CHACHA20-POLY1305:ECDHE-RSA-CHACHA20-POLY1305:DHE-RSA-CHACHA20-POLY1305:ECDHE-RSA-AES256-GCM-SHA384:ECDHE-RSA-AES128-GCM-SHA256:DHE-RSA-AES256-GCM-SHA384:ECDHE-RSA-AES256-SHA384:ECDHE-RSA-AES256-SHA:DHE-RSA-AES256-SHA256:DHE-RSA-AES256-SHA:!RC4:!LOW:!MD5:!aNULL:!eNULL:!3DES:!EXP:!PSK:!SRP:!DSS
</IfDefine>

#   SSL Honer Cipher Suite Order:
#   Forces the order of allowed cipher suites to the order above.
#   See the mod_ssl documentation for a complete list.
SSLHonorCipherOrder On

#   Pass Phrase Dialog:
#   Configure the pass phrase gathering process.
#   The filtering dialog program (`builtin' is a internal
#   terminal dialog) has to provide the pass phrase on stdout.
SSLPassPhraseDialog  builtin

#   Inter-Process Session Cache:
#   Configure the SSL Session Cache: First the mechanism
#   to use and second the expiring timeout (in seconds).
#SSLSessionCache         "dbm:${SRVROOT}/logs/ssl_scache"
SSLSessionCache        "shmcb:${SRVROOT}/logs/ssl_scache(512000)"
SSLSessionCacheTimeout  300

#
#   Some MIME-types for downloading Certificates and CRLs
#
AddType application/x-x509-ca-cert .crt
AddType application/x-pkcs7-crl    .crl

#   SSL Engine Options:
#   Set various options for the SSL engine.
#   o FakeBasicAuth:
#     Translate the client X.509 into a Basic Authorisation.  This means that
#     the standard Auth/DBMAuth methods can be used for access control.  The
#     user name is the `one line' version of the client's X.509 certificate.
#     Note that no password is obtained from the user. Every entry in the user
#     file needs this password: `xxj31ZMTZzkVA'.
#   o ExportCertData:
#     This exports two additional environment variables: SSL_CLIENT_CERT and
#     SSL_SERVER_CERT. These contain the PEM-encoded certificates of the
#     server (always existing) and the client (only existing when client
#     authentication is used). This can be used to import the certificates
#     into CGI scripts.
#   o StdEnvVars:
#     This exports the standard SSL/TLS related `SSL_*' environment variables.
#     Per default this exportation is switched off for performance reasons,
#     because the extraction step is an expensive operation and is usually
#     useless for serving static content. So one usually enables the
#     exportation for CGI and SSI requests only.
#   o StrictRequire:
#     This denies access when "SSLRequireSSL" or "SSLRequire" applied even
#     under a "Satisfy any" situation, i.e. when it applies access is denied
#     and no other module can change it.
#   o OptRenegotiate:
#     This enables optimized SSL connection renegotiation handling when SSL
#     directives are used in per-directory context.
#SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire
<FilesMatch "\.(cgi|shtml|phtml|php)$">
    SSLOptions +StdEnvVars
</FilesMatch>
<Directory "${SRVROOT}/cgi-bin">
    SSLOptions +StdEnvVars
</Directory>

#   SSL Protocol Adjustments:
#   The safe and default but still SSL/TLS standard compliant shutdown
#   approach is that mod_ssl sends the close notify alert but doesn't wait for
#   the close notify alert from client. When you need a different shutdown
#   approach you can use one of the following variables:
#   o ssl-unclean-shutdown:
#     This forces an unclean shutdown when the connection is closed, i.e. no
#     SSL close notify alert is sent or allowed to be received.  This violates
#     the SSL/TLS standard but is needed for some brain-dead browsers. Use
#     this when you receive I/O errors because of the standard approach where
#     mod_ssl sends the close notify alert.
#   o ssl-accurate-shutdown:
#     This forces an accurate shutdown when the connection is closed, i.e. a
#     SSL close notify alert is send and mod_ssl waits for the close notify
#     alert of the client. This is 100% SSL/TLS standard compliant, but in
#     practice often causes hanging connections with brain-dead browsers. Use
#     this only for browsers where you know that their SSL implementation
#     works correctly.
#   Notice: Most problems of broken clients are also related to the HTTP
#   keep-alive facility, so you usually additionally want to disable
#   keep-alive for those clients, too. Use variable "nokeepalive" for this.
#   Similarly, one has to force some clients to use HTTP/1.0 to workaround
#   their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and
#   "force-response-1.0" for this.
BrowserMatch "MSIE [2-5]" \
         nokeepalive ssl-unclean-shutdown \
         downgrade-1.0 force-response-1.0

#   Per-Server Logging:
#   The home of a custom SSL log file. Use this when you want a
#   compact non-error SSL logfile on a virtual host basis.
CustomLog "${SRVROOT}/logs/ssl_request.log" \
          "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" env=HTTPS

##
## SSL Virtual Host Context
##
<VirtualHost _default_:80>
  DocumentRoot "c:/xampp/htdocs"
</virtualhost>

<VirtualHost _default_:443>
  SSLEngine on
  ServerName localhost:443
  SSLCertificateFile "conf/ssl.crt/server.crt"
  SSLCertificateKeyFile "conf/ssl.key/server.key"
  DocumentRoot "c:/xampp/htdocs"
# DocumentRoot access handled globally in httpd.conf
</virtualhost>



# End SNI Demonstration Config



Tested.
Code: Select all
d:\curl>curl -k --verbose --http2 --tlsv1.3 https://localhost
*   Trying ::1...
* TCP_NODELAY set
* Connected to localhost (::1) port 443 (#0)
* ALPN, offering h2
* ALPN, offering http/1.1
* TLSv1.3 (OUT), TLS handshake, Client hello (1):
* TLSv1.3 (IN), TLS handshake, Server hello (2):
* TLSv1.3 (IN), TLS handshake, Encrypted Extensions (8):
* TLSv1.3 (IN), TLS handshake, Certificate (11):
* TLSv1.3 (IN), TLS handshake, CERT verify (15):
* TLSv1.3 (IN), TLS handshake, Finished (20):
* TLSv1.3 (OUT), TLS change cipher, Change cipher spec (1):
* TLSv1.3 (OUT), TLS handshake, Finished (20):
* SSL connection using TLSv1.3 / TLS_CHACHA20_POLY1305_SHA256
* ALPN, server accepted to use h2
* Server certificate:
*  subject: CN=localhost
*  start date: Nov 10 23:48:47 2009 GMT
*  expire date: Nov  8 23:48:47 2019 GMT
*  issuer: CN=localhost
*  SSL certificate verify result: self signed certificate (18), continuing anyway.
* Using HTTP2, server supports multi-use
* Connection state changed (HTTP/2 confirmed)
* Copying HTTP/2 data in stream buffer to connection buffer after upgrade: len=0
* Using Stream ID: 1 (easy handle 0x103e710)
> GET / HTTP/2
> Host: localhost
> User-Agent: curl/7.64.1
> Accept: */*
>
* TLSv1.3 (IN), TLS handshake, Newsession Ticket (4):
* TLSv1.3 (IN), TLS handshake, Newsession Ticket (4):
* old SSL session ID is stale, removing
* Connection state changed (MAX_CONCURRENT_STREAMS == 100)!
< HTTP/2 302
< date: Tue, 18 Feb 2020 20:56:00 GMT
< server: Apache/2.4.41 (Win64) OpenSSL/1.1.1c PHP/7.4.1
< x-powered-by: PHP/7.4.1
< location: https://localhost/dashboard/
< content-length: 0
< content-type: text/html; charset=UTF-8
<
* Connection #0 to host localhost left intact
* Closing connection 0
gsmith
 
Posts: 265
Joined: 29. November 2013 18:04
Location: San Diego
XAMPP version: 0.0.0
Operating System: Win 10/2012R VS 14,15,16

Re: Help with SSL

Postby smurfier » 19. February 2020 18:06

gsmith, you are amazing. Thank you soooo much.
smurfier
 
Posts: 3
Joined: 17. February 2020 05:36
XAMPP version: 3.2.4
Operating System: Windows 10Pro


Return to XAMPP for Windows

Who is online

Users browsing this forum: No registered users and 78 guests